Blomberg DWT25502SS Instalační manuál

www.blomberginternational.cominfo@blomberginternational.comDishwasherInstallation ManualDWT 56502 SSDWT 58500 BDWT 58500 FBIDWT 58500 SSDWT 58500 SSWS

7USAAdjust the front foot level with the adjusting wrench to balance and raise the dishwasher to the enclosure height.Adjust the rear foot level with

8USA6.5 PREPARING THE WATER CONNECTION (A)Install an easily accessible shut-off valve (not supplied) in the water supply line. All solder connections

9USA6.6 DRAIN PREPARATIONThe dishwasher drain hose may be connected to the drain plumbing in one of three ways (Figure A, B, C). NOTICE :• Either one

10USA6.7 STEAM PROTECTION FOILSteam will form inside the dishwasher during operation. At the end of the cycle, when the dishwasher door is opened, it

11USA7. PLACEMENT OF DISHWASHER INTO THE OPENINGNow place the dishwasher into the opening and get ready to connect all hoses and electrical connection

12USA7.1.2 PREPERATION OF WATER SUPPLYLeft side water supply connectionBefore pushing the dishwasher in to the cabinet you must place water supply

13USAAfter installing one clip for each side push the dishwasher into the cabinet (Figure E).Note that while pushing the dishwasher into the cabine

14USA7.1.3 WATER SUPPLY CONNECTIONWater supply may be connected to the dishwasher in one of two ways:• With metal braided hose.• With copper tubing.

15USA7.3 ADJUSTING THE MOVABLE TOE KICKNow that you have successfully installed the dishwasher, you need to attach the toe kick to the dishwasher. The

16USAIf the enclosure height is below 331/16” (840mm) use only “o” labelled toe kick (toe kick without slots). Installation should be don

DishwasherInstallation ManualDWT 56502 SSDWT 58500 BDWT 58500 FBIDWT 58500 SSDWT 58500 SSWSDWT 58500 WDWT 59500 FBIDWT 59500 SSDWT 25502 BDWT 25502 SS

17USA2. To take the plastic bracket out, remove the screws on it. Screws will be used in 5th step again. (Figure B).3. Mark the wooden door as show

18USA5. Attach the two mounting brackets to the wooden door with 4 screws (Ø 1/8” x 5/8” (Ø 3.5mm x 14mm) (Figure A).6. Mount the w

19USA8. Using the four screws Ø 3/16” x 111/16” (Ø 4mm x 43mm) provided, attach the wooden door to the dishwasher a

20USA11. Check whether the bottom of the door hits the toe kick of the kitchen cabinet (A).11.1. If the door hits the toe kick cut the necessar

21USA NOTICE :If you have a European kitchen or want to install a wooden toe kick to match

22USA15 0575 0100_AA Installation Manual_USA/ 25-08-16.(8:30)8. INSTALLER CHECKLISTYour installer must have completed and checked the following:• The

[email protected]

INTRODUCTION 11. IMPORTANT SAFETY INSTRUCTIONS 11.1 INSPECT THE DISHWASHER 21.2 HOW TO CONTACT US : 22. TOOLS WHICH MAY BE NEEDED 33. MATERIALS WH

1USAINTRODUCTIONPlease read this installation manual and particularly the safety instructions completely and carefully. They will save you time and ef

2USAcabinetry using the brackets provided. Failure to do this may cause damage to property or bodily injury.• Connect to a properly rated, protected

3USA2. TOOLS WHICH MAY BE NEEDED3. MATERIALS WHICH MAY BE NEEDED(Additional materials may be required to comply with local codes)Hot Water Supply Line

4USA4. MATERIALS SUPPLIED4.1 PARTS SUPPLIEDParts for your dishwash

5USA5. DISHWASHER SPECIFICATIONS5

6USA6. ENCLOSURE PREPARATION6.1 ELECTRICAL PREPARATION WARNINGThe dishwasher is designed for an electrical supply of 120 V, 60 Hz, AC, connected to a